自适应现状制导律

针对反弹道导弹的导弹武器的主动飞行段,提出了高精度自适应现状制导律。通过实时修正飞行程序,以消除导弹飞行过程中遇到的各种干扰的影响,保证命中精度,并对发动机推力偏差、风干扰影响下的导弹运动进行了数学仿真,仿真结果证实了自适应现状制导律是合理、可行的。     

B4C/Al复合板中应力波行为分析（Ⅰ）

依据7.62mm穿甲燃烧弹与B4C,Al板的物理和力学特性,提出弹、板的力学模型;在此基础上,给出弹板碰撞后B4C/Al复合板的弹性动力学方程,建立应力波的传播模型,讨论了应力波传播时复合板的力学行为,最后确定了复合板承受的初始冲击应力。理论分析表明：一维应变条件的B4C和Al板的弹性极限高于一维应力条件下的值;弹、板间的作用力服从指数衰减规律;B4C板的初始应力高于430MPa时,应力波的作用使Al板在卸载过程中发生反向屈服。     

Development of cost effective personnel armour through structural hybridization

The objective of the present study is to develop cost effective thermoplastic hybrid laminate using Dyneema® HB50 and Tensylon®HSBD 30A through structural hybridization method. Laminates having 20 mm thickness were fabricated and subjected to 7.62 × 39 mm mild steel core projectile with an impact velocity of 730 ± 10 ms⁻¹. Parameters such as energy absorption, back face deformation and rate of back face deformation were measured as a function of hybridization ratio. It was observed that hybrid laminate with 50:50 ratio (w/w) of Tensylon® and Dyneema® with Tensylon® as front face showed 200% more energy absorption when compared to 100% Tensylon® laminate and showed equal energy absorption as that of expensive 100% Dyneema® laminate. Moreover, hybrid laminate with TD50:50 ratio showed 40% lower in terms of final back face deformation than Dyneema® laminate. Rate of back face deformation was also found to be slow for hybrid laminate as compared to Dyneema® laminate. Dynamic mechanical analysis showed that, Tensylon® laminate has got higher stiffness and lower damping factor than Dyneema® and hybrid laminates. The interface between Tensylon® and Dyneema® layers was found to be separating during the penetration process due to the poor interfacial bonding. Failure behaviour of laminates for different hybridization ratios were studied by sectioning the impacted laminates. It was observed that, the Tensylon® laminate has undergone shear cutting of fibers as major failure mode whereas the hybrid laminate showed shear cutting followed by tensile stretching, fiber pull out and delamination. These inputs are highly useful for body armour applications to design cost effective armour with enhanced performance.     

超声冲击处理改善22SiMn2TiB装甲钢抗应力腐蚀性能研究

采用超声冲击处理工艺对22SiMn2TiB装甲钢试样进行了表面冲击强化,采用四点弯曲加载装置将处理和未处理的试样在3.5%NaCl溶液中进行了150 d的应力腐蚀试验。用X射线应力测定仪测定了应力腐蚀试验前试样表面的残余应力,用扫描电镜和透射电镜观察了处理后试样的断面组织。分析了超声冲击处理引起的残余应力和断面组织变化对改善装甲钢抗应力腐蚀性能的作用。结果表明,超声冲击处理引入的残余压应力和表层晶粒细化可以大大提高22SiMn2TiB装甲钢的抗应力腐蚀性能。     

导弹制导控制与目标杀伤

采用协方差分析描述函数技术 (CADFT)对寻的导弹的制导精度进行了研究 ,提出了空气动力控制、直接侧向力控制的寻的导弹飞行末端的制导精度的一种新的解析模型 ,并研究了导弹直接碰撞杀伤目标的必要条件 ,该理论研究成果具有简单、实用、精度高的特点 ,为寻的导弹制导控制特性研究和揭示寻的理论普遍规律提供了一种新途径     

Characteristics structure analysis on debris cloud in the hypervelocity impact of disk projectile on thin plate

In this paper, the gauge points setting is introduced in the SPH simulation to analyze the debris cloud structure generated by the hypervelocity impact of disk projectile on thin plate. Compared with the experiments, more detailed information of the debris cloud structure can be classified from the numerical simulation. However, due to the solitary dispersion and overlap display of the particles in the SPH simulation, accurate comparison between numerical and experimental results is difficult to be performed. To track the velocity and spatial distribution of the particles in the debris cloud induced from disk and plate, gauge points are locally set in the single-layer profile in the SPH model. By analyzing the gauge points’ spatial coordinate and velocity, the location and velocity of characteristic points in the debris cloud are determined. The boundary of debris cloud is achieved, as well as the fragments distribution outside the main structure of debris cloud.     

利用MSC/DYTRAN程序仿真分析导弹战斗部立方体破片的侵彻威力

对反辐射导弹的破片杀伤战斗部中较为常见的立方体破片的 3种典型姿态侵彻 (尖端、棱边及正面侵彻 ) 4mm厚 94 5钢的侵彻过程进行仿真数值计算 .通过仿真计算 ,结合实验结果比较 ,得出结论 :不同初始侵彻姿态的立方体破片在侵彻过程中 ,由于旋转角速度的作用及稳定性的要求 ,破片的侵彻姿态将趋于正面侵彻 .不同姿态的侵彻 ,侵彻威力相差不大     

燃气射流引起的火箭发射系统振动特性分析

以火箭发射系统为研究对象,对其56°射角工况下发射过程中的振动特性进行分析。创新点在于确定发射过程中动态载荷的加载方法,即首先根据发射系统有限元分析结果确定迎气面上试验测量点的具体位置,然后测得燃气射流冲击压强随时间变化的数值,并对试验测得数据进行处理,最后推导冲击压力对于径向距离的直线公式。所采用的冲击压强分析方法为研究其他武器系统受燃气射流冲击的影响提供了重要的指导意义。     

基于遭遇角决策的并行双模切换舵减摇控制

结合舵减摇控制中通用线性模型与模糊线性模型的优缺点,采用了一种根据遭遇角的不同自动切换控制器设计模型的并行双模切换舵减摇控制方案。为在线自动辨识遭遇角,提出基于横摇功率谱密度柱状图的神经网络辨识方法。仿真结果表明,该方法辨识精度较高,且比传统重心法节省了在线计算量与存储数据库所需的存储空间,简化了辨识流程。     

大攻角飞行导弹自动驾驶仪反馈线性化设计

针对大攻角空空导弹飞行过程中复杂的非线性空气动力学特性,提出了采用反馈线性化进行控制器设计的方法.在完成导弹俯仰通道的非线性建模的基础上,采用反馈线性化理论对导弹模型进行精确线性化,然后,对线性化后的系统给出了变结构控制系统设计.最后,通过仿真验证了所设计的控制器具有良好的动态性能及较好的工程参考价值.